What is the correct way to install solar led street light?
solar led street light should be able to better meet the requirements of night use, and solar led street light manufacturers can meet people's lighting needs and normal use, so we must pay more attention to the correct use and installation of LED in the process of use.
(1) When using high-power ledsolar led street light, it must be installed according to the actual lighting requirements of the site, and adjust the position and height of the lamp.
(2) Secondly, we should determine the appropriate lamp installation method. LEDsolar led street light manufacturers adjust the installation bracket, and then prepare the corresponding length of the three-core bar according to the distance between the lamp and the power connection.
(3) Open the buckle at the front end of the lamp by hand, open the top cover of the lamp, and lead the wiring into the lamp cavity through the filling hole at the back of the lamp. Connect the cable according to the polarity marked on the socket inside the lamp.
(4) It should be noted that after the connection of ledsolar led street light, the line must be pressed tightly with a wire press.
(5) Insert the light pole into the lead-in hole of the installation bracket, place the light pole into the tube of the bracket at the appropriate position according to the Angle required for lighting, and tighten the pressing bolt of the light pole. Securely connected to light fixture.
solar led street light is compact and small. To reflect its advantages, its design and performance have been upgraded. For example, the battery uses a lithium iron phosphate battery and a high-conversion monocrystal silicon cell. A lot of effort has been put into the appearance, the waterproofing, and the connection between the components.
solar led street light is an emerging product and an environmental protection product. It is convenient for people to travel on both sides of large highways. In fact, the advantages of solar led street light are also obvious, so many units begin to try to apply this kind of street light, including signal lights, landscape lights, lawn lights, etc., to add luster to the landscape of the park.
Many people think, solar led street light is only one kind of show of science and technology strength, in fact, this statement is not a problem, the application of ledsolar led street light however explains our country application of high-tech products strength. But it is worth attention. We use ledsolar led street light because this kind of energy belongs to clean energy, which will not pollute the surrounding environment and does no harm to human living environment. Therefore, it is applied and promoted by people.
Another reason for large-scale units to adopt ledsolar led street light is that this kind of street light is relatively economical. Although it is a high product in terms of installation and product costs, it does not need to consume external electric energy in later use. It only needs to convert heat energy into electricity needed by itself. Therefore, it will save a great deal of electricity costs. In addition, its later repair will be less. Such street lamps are really beneficial to the country and the people, and the contribution of thousands of generations.
solar led street light When installing the solar maintenance-free battery, put it into the control box and handle it gently to prevent damage to the control box; Cables between batteries must be bolted to the battery. After the output cables are connected to the battery, do not short circuit in any case to avoid damage to the battery. When the output line of the battery is connected to the controller in the pole, it is threaded through the PVC conduit.
Check the wiring of the controller to prevent short circuit. Close the door of the control box when normal. Check whether the fasteners in each part are firm, whether the lamp holder is installed correctly, and whether the light source works normally. Then check whether the system runs normally, loosen the connection line between the controller and the solar panel, the light source works normally, connect the connection line of the solar panel, and the light goes out; At the same time, carefully observe the change of each indicator on the controller. If the data is normal, you can lift it.
When hoisting the main light pole, the screws must be fastened. If the component has a wrong sunrise Angle, it needs to be adjusted upward so that the sunrise direction is completely south.
Put the battery in the battery box, connect the cable to the controller according to the technical requirements, first connect the battery, then connect the load, then connect the solar panel; When wiring, we must pay attention to the connection of each wire and the terminal marked on the controller can not be wrong, positive and negative terminals can not collide, do not connect the reverse, otherwise it will damage the controller.
Debug again to see if the system can run normally; Loosen the solar panel connection cable on the controller, and the LEDsolar led street light will turn on. Connect the solar panel connection cable, and the light will turn off. At the same time, carefully observe the change of the indicators on the controller, the data is normal, the control box can be sealed.
solar powered street lights What are the several ways to control the lights?
Precautions for using solar powered street lights
What is the lifespan of solar powered street lights?
What is the standard spacing of solar led street light installation?
